Connect Via SDI

SDI Guide← Back to Get Started

This guide covers setting up SimplTrack3 with its 3G-SDI video output. The SimplTrack3 supports video resolutions up to 1080p over SDI.

📋What you need

• 3G SDI cable (75-ohm BNC)
• 12V DC power supply (included) or PoE (802.3af) switch or injector
• A video switcher, capture card, or monitor with SDI input
• Optional: Ethernet cable for network control

Connect SDI

Connect the 3G-SDI Cable

1. Connect a 75-ohm 3G-SDI cable (BNC) from the camera's SDI output to your video switcher, capture card, or monitor's SDI input.

📋Use proper SDI cables

Standard composite or component BNC cables will not carry an SDI signal reliably. Use a 3G 75-ohm-rated cable.

Connect Power and Network

Choose one of the following power methods:

Option A: 12V DC Power Supply

1. Connect the included 12V DC power supply to the camera's DC input.
2. Plug the power supply into a standard wall outlet.

Option B: Power over Ethernet

Power over Ethernet PoE (802.3af)

1. Connect an Ethernet cable from a PoE (802.3af) switch or PoE (802.3af) injector to the camera's LAN port.
2. The camera will power on automatically.

Wait for Startup Sequence

When powered, the SimplTrack3 camera performs a startup sequence:

1️⃣

Self-calibration: During startup, the camera moves through its full range of motion while both the green (Standby) and blue (Power) LEDs are on. When self-calibration is complete, the camera returns to Preset 0

2️⃣

Ready: Once the camera stops moving and the green LED turns off, your camera is ready to use.

Control the Camera

Use the following options to quickly verify control of the camera.

Option A: Network Control (Recommended)

If the SimplTrack3 camera is connected to your network, you can control it from the SimplTrack3 Web UI.

1. Open a browser and go to http://ptzoptics.local/
2. Log in with your credentials.
3. Use the SimplTrack3 Web UI for full PTZ control, image settings, and preset management.

Option B: IR Remote (Simplest)

Use the included IR remote to pan, tilt, zoom, and save presets. Point the remote at the camera's front sensor.

Button	Action
⬆️⬇️⬅️➡️ Arrow keys	Pan left/right and tilt up/down
Tele / Wide	Zoom in and out
Home	Return to Home Position
[Number] + [SET]	Save a preset

Save Your First Preset

Using the Web Interface

1. Move the camera to your desired position.
2. Click Set in the Preset Control section.
3. Enter a preset number and press Enter.

Using a PTZ Joystick (e.g., SuperJoy)

1. Move the camera to your desired position.
2. Press the Preset button on the joystick.
3. Enter the preset number and confirm.

Using the IR Remote

Press a number (e.g., [1]) followed by [SET] to save. To recall, press the number followed by [CALL]. For more information on using the IR remote, see the Using the IR Remote section.

SDI Specifications

3G-SDI Specifications

Feature	Specification
Max Resolution	1080p @ 60fps (1920 × 1080)
Max Cable Length	~200–328 ft (60–100 m) with quality cable
Audio	Yes. This camera supports embedded audio over SDI.
Connectors	BNC (locking)
Signal Type	3G-SDI (Level-A or Level-B)

⚠️More Information on Camera Control

This camera can be controlled using various methods and joystick controllers. To learn more about camera control, see Control Options.

Next Steps

• Adjust image settings for your lighting conditions
• Configure streaming protocols if you also need network video output

← Back to Get Started